Accueil / Équipements / Scelleuse d’emballages thermoformés / Blister/Thermoforming Packaging Sealer

SED-570-450XSJ-A

Sur devis

SED-570-450XSJ-A

SED · SED-570-450XSJ-A · En vedette

SED-570-450XSJ-A — Blister/Thermoforming Packaging Sealer

La description complète de ce modèle est encore en cours de traduction. Consultez les détails en anglais ou demandez des informations à notre équipe. English

SED-570*450XSJ-A is an automatic pressure-vacuum (positive + negative pressure) high-speed thermoforming machine with continuous 4-station operation: forming, punching, cutting, and manipulator stacking. Forms films in P

Délai de livraison

Sur devis

Cadence

35 molds/min

Fonctionnement

Pressure-vacuum (combined positive + negative pressure) thermoforming. Servo film-feed conveys plastic sheet through a patented sealed heating oven that brings it to forming temperature. The heated sheet enters the forming station where 6 servo-driven mold clamps close, and combined air pressure + vacuum forces the film into the mold cavities. The web then advances to a punching station (with optional indentation, bottom-hole and side-hole punching), then a transfer-cutting station with ±0.4 mm deviation, then a servo manipulator picks the parts and stacks them on a 2 m conveyor. Waste film is automatically rolled up; an in-line pulverizer can recycle scrap. Delta PLC + 10.4-inch Taiwan touch screen controls the line; Delta temperature controller maintains ±0.5 °C across multiple independently controlled heating zones with auto-compensation.

Processus de fonctionnement

1Pressure-vacuum (combined positive + negative pressure) thermoforming.

2Servo film-feed conveys plastic sheet through a patented sealed heating oven that brings it to forming temperature.

3The heated sheet enters the forming station where 6 servo-driven mold clamps close, and combined air pressure + vacuum forces the film into the mold cavities.

4The web then advances to a punching station (with optional indentation, bottom-hole and side-hole punching), then a transfer-cutting station with ±0.4 mm deviation, then a servo manipulator picks the parts and stacks them on a 2 m conveyor.

5Waste film is automatically rolled up; an in-line pulverizer can recycle scrap.

6Delta PLC + 10.4-inch Taiwan touch screen controls the line; Delta temperature controller maintains ±0.5 °C across multiple independently controlled heating zones with auto-compensation.

Caractéristiques techniques

Caractéristiques de la variante : SED-570-450XSJ-A

Caractéristiques

Modèle

SED-570-450XSJ-A

Cadence

35 molds/min

Tension

380V 50/60Hz

Puissance

75 kW

Pression d’air

0.6-0.8 MPa, 0.5-3 m^3/min

Dimensions

Longueur

9000 mm

Largeur

1600 mm

Hauteur

2400 mm

Poids

7000 kg

Matériaux

Matériaux du bâti

120×60×5 / 120×60×3 mm square-tube frame; 300 steel die set frame, alloy steel columns; nitrided forged feed chain; alloy steel pin shaft; self-lubricating bearings

Caractéristiques principales

Continuous 4-station: forming, punching, cutting, manipulator stacking

Max forming area 570 × 450 mm, depth 80 mm

Sheet 610 mm wide, 0.12–2 mm thick

Up to 35 molds/min

Pressure-vacuum (positive + negative pressure) forming with multiple modes

Patented sealed insulated heating oven (~30% energy saving vs. market)

6 × 1.8 kW Delta/Inovance servo mold clamps

Servo manipulator (3 kW + 0.8 kW) up to 35 cycles/min, 2 m stacking conveyor

Delta temperature controller, ±0.5 °C, independent point control

Cutting deviation ±0.4 mm; transfer cutting mode

Bidirectionally controlled mold board

In-line: indentation, bottom-hole punching, side-hole punching, edge cutting

Auto film feed, mold positioning, auto loading, waste rolling

Auto oven retreat on power-off / fault

10.4-inch Taiwan touch screen, Delta/Inovance medium PLC

Includes 100 L vacuum pump + 3 HP air-cooled chiller

Total electricity consumption ~150 kWh/ton of film

8-direction fine adjustment on cutting mold; electric chain-width adjustment (4 sets)

30% lower electricity vs. competing thermoformers thanks to patented oven

Servo manipulator removes need for human stacking and separate cutting machine

±0.4 mm cutting and ±0.5 °C heat control deliver tight tolerances

Wide material compatibility: PP, PE, PET, PVC, PETG, PS, ABS, EPS, APET, HIPS

Premium components: SMC/AirTAC pneumatics, THK rails, Delta/Inovance servos and PLC, AUTONICS sensors, Schneider/Omron/CHINT electrics, Harbin bearings

Applications

Electronics: semi-finished trays, electronics packaging

Frozen food trays, cup lids, bento boxes, jelly cups, moon cake trays

Fruit and vegetable trays / packaging boxes

Pharma: injection trays, solid/liquid medicine trays, bottle trays

Refrigerator inner liners, appliance blister parts and packaging

Tool packaging, alcohol packaging trays

Agricultural flowerpots, seeding trays

Auto parts blister packaging, helmet liners

Secteurs

Plastic packaging

Food packaging

Pharmaceutical packaging

Electronics

Appliance

Agriculture

Automotive

Tools / hardware

Marques des composants

Servo motors and drives

Delta / Inovance

PLC (medium)

Delta / Inovance

Touch screen 10.4-inch

Taiwan

Photoelectric switch

AUTONICS

Solid-state relay

Italy / XIZI

Relay

Omron / Schneider

Pneumatic valves and cylinders

SMC / AirTAC

Vacuum valve (1")

SMC

Electrical components

Schneider / CHINT

Bearings

Harbin

Reducer motor

Jiangsu Jiangyan

Reducer

Taiwan

Linear sliding rail

THK

SED

Échangez avec SED Sales Team

Spécialistes des équipements · contact sur WhatsApp

Consultez les horaires et la disponibilité de l’équipe

+86 139 5885 3738

Envoyer un e-mail Discuter sur WhatsApp →Demander un appel de 30 minutes →