صالة عرض في أونتاريو، كاليفورنيا · استفسر عن الدعم في وجهتك
SED-10SZ-H
حسب الطلب
SED-10SZ-H خلاط محبب رطب
SED · SED-10SZ-H · 1 وحدة مباعة

SED-10SZ-H — خلاط محبب رطب

لا تزال ترجمة الوصف الكامل لهذا الطراز قيد العمل. راجع التفاصيل بالإنجليزية أو اطلب المعلومات من فريقنا. English

SED-10SZ-H Wet Mixing Granulator (high-shear wet mixer-granulator). New-generation pharmaceutical equipment that quickly mixes dry powder and produces homogeneous wet granules in one step. Combines mixing and granulation

GMP compliant
مدة التسليم
حسب الطلب
الطاقة الإنتاجية
4–24 kg/hour

مبدأ العمل

Three-blade impeller in a SUS304 mixing drum performs a regular spiral 3D motion that fully blends raw and auxiliary materials, including those at the bottom. After binder is added and material is wetted, an independently driven multi-layer herringbone chopper rotates at high speed to cut agglomerates into uniform granules. Mixing, wetting, and granulation run continuously, finishing in roughly ten minutes. Pneumatic discharge valve and air-sealed shafts on both impeller and chopper prevent contamination.

وصف سير العمل
1Three-blade impeller in a SUS304 mixing drum performs a regular spiral 3D motion that fully blends raw and auxiliary materials, including those at the bottom.
2After binder is added and material is wetted, an independently driven multi-layer herringbone chopper rotates at high speed to cut agglomerates into uniform granules.
3Mixing, wetting, and granulation run continuously, finishing in roughly ten minutes.
4Pneumatic discharge valve and air-sealed shafts on both impeller and chopper prevent contamination.

المواصفات الفنية

مواصفات التكوين: SED-10SZ-H

المواصفات

الطراز
SED-10SZ-H
الطاقة الإنتاجية
4–24 kg/hour
المرافق
Electrical supply for 2.2 kW mixing motor + 0.75–1.1 kW chopper motor; compressed air ≥ 0.5 MPa for shaft air-seal and pneumatic discharge cylinder.
تفاصيل المطابقة
Conforms to GMP standards. Compressed air above 0.5 MPa required for shaft air-seal during operation.
القدرة
3.3 kW

الأبعاد

الطول
1300 mm
العرض
650 mm
الارتفاع
1200 mm
الوزن
182 kg
مساحة التركيب
1300 mm x 650 mm floor footprint, 1200 mm tall; no foundation required, install on level ground; allow surrounding clearance for maintenance.

المواد

مواد التلامس
SUS304; silicone rubber(lid seal)
مواد الهيكل
5# channel-steel welded frame; SUS304(drum, paddles, chopper, frame panels)

الخصائص الرئيسية

Drum volume: 10 L
Output: 3 kg/batch
Mixing speed: 300/600 rpm(low/high)
Mixing motor power: 1.5/2.2 kW(dual speed)
Cutting(chopper) speed: 1500/3000 rpm
Cutting motor power: 0.85/1.1 kW
Cylindrical bottom + conical top SUS304 drum, no dead corners
Pneumatic discharge valve on drum bottom
Silicone rubber lid seal + air-seal on drive shafts
Safety interlock: cannot start when lid open or discharge cleaning open
Granulation cycle~10 minutes
Saves 20-25% binder vs. older granulators; shortens drying time
Combinable with one-step boiling granulator/dryer
Dimensions: 1300 x 650 x 1200 mm
Weight: 182 kg
Total power: 3.3 kW
GMP compliant
4× efficiency over traditional swing granulators
One-step mix + wet + granulate eliminates manual contact contamination
Reliable air-sealed shafts and pneumatic discharge valve
Built with SUS304 stainless contact surfaces
Reproducible parameters via current monitoring at end-point

التطبيقات

Pharmaceutical wet granulation
Health-product wet granulation
Food powder granulation
Cosmetic granulation
Powder metallurgy
Dye and detergent granulation

القطاعات

الأدوية
Chemical
Food
Powder metallurgy
مستحضرات التجميل
Dyes
Detergents

العلامات التجارية للمكونات

Chint (electrical)
SED
تواصل مع SED Sales Team
متخصصو المعدات · تواصل عبر واتساب
استفسر عن مواعيد العمل وتوفر الفريق

الامتثال

GMP compliant

التنظيف والصيانة

Add water into the drum and start mixer impeller and chopper to wash; discharge port and lid have sealing components for clean operation. Periodically drain the air source oil-water separator to prevent water accumulation. Inspect drum lid sealing strip and replace if damaged.

الوثائق

ورقة البيانات (PDF)
نظرة عامة على المعدات والمواصفات والأبعاد · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
دليل التشغيل
التركيب والتشغيل واستكشاف الأعطال · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
ورقة مقارنة (قياسي واقتصادي)
مقارنة التكوينات · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
بروتوكولات IQ / OQ / PQ
وثائق التحقق لمطابقة GMP · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
بروتوكولات FAT / SAT
اختبارات القبول في المصنع وفي الموقع · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
رسومات CAD (STEP / IGES / DWG)
رسومات هندسية لتخطيط المنشأة · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
شهادات المعايرة
مستوى الصوت ومقاومة التأريض والعزل وخشونة السطح · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
DQ (تأهيل التصميم)
بروتوكول كامل لتأهيل التصميم · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
شهادات المواد
تركيب الفولاذ المقاوم للصدأ 316L · المستند الأصلي (الإنجليزية)
اطلب من فريق المبيعات
SED
واتساب · مبيعات SED
التواصل مع المبيعات · واتساب
→