Accueil / Équipements / Centrifugeuse tubulaire / SED-42LXJ-T 45-Type Tubular Centrifuge (Clarification Type)

SED-42LXJ-T

Sur devis

SED-42LXJ-T

SED · SED-42LXJ-T · En vedette

SED-42LXJ-T — SED-42LXJ-T 45-Type Tubular Centrifuge

La description complète de ce modèle est encore en cours de traduction. Consultez les détails en anglais ou demandez des informations à notre équipe. English

SED-42LXJ-T is a 45-type clarification-type tubular centrifuge for separating dilute, viscous emulsions and suspensions where solid-phase particles are extremely fine and density differences between phases are very small

Choisir une variante (1)

Délai de livraison

Sur devis

Cadence

80 L/h

Fonctionnement

Liquid feed enters the bottom of a vertical thin-walled rotating bowl through a feeding nozzle. Centrifugal force at up to ~18,500 G drives the heavier phase (solids) to adhere to the bowl wall while clarified liquid overflows the top into the collection pan. When the bowl fills with solids, the machine is stopped, the bowl removed via wrench, and solids scraped out. A check-valve bowl cover prevents back-flow contamination on stop. Voltage-regulator stepless speed control (max 175V) plus high-speed belt drive lets operators tune G-force to material characteristics. Optional cooling coil maintains feed temperature for heat-sensitive bio products.

Processus de fonctionnement

1Liquid feed enters the bottom of a vertical thin-walled rotating bowl through a feeding nozzle.

2Centrifugal force at up to ~18,500 G drives the heavier phase (solids) to adhere to the bowl wall while clarified liquid overflows the top into the collection pan.

3When the bowl fills with solids, the machine is stopped, the bowl removed via wrench, and solids scraped out.

4A check-valve bowl cover prevents back-flow contamination on stop.

5Voltage-regulator stepless speed control (max 175V) plus high-speed belt drive lets operators tune G-force to material characteristics.

6Optional cooling coil maintains feed temperature for heat-sensitive bio products.

Caractéristiques techniques

Caractéristiques de la variante : SED-42LXJ-T clarification-type bowl (liquid-solid separation only)

Caractéristiques

Modèle

SED-42LXJ-T

Cadence

80 L/h

Fluides et énergie

Single-phase series motor with voltage regulator (max 175 V output; start at 125-150 V). Reliable ground connection on machine body. Vent pipe if separating toxic materials. Optional cooling water supply for bioengineering jacket.

Détails de conformité

Manufactured per ZBJ7708-89 'Tubular Separator Technical Specification' (China). Idle/load vibration intensity <= 7.1 mm/s; load motor temperature rise <= 30 C; load regulator temperature rise <= 25 C; idle speed reduction allowable 1%, loaded 3%. Bowl balance precision A=2.5 grade; total de-weight of bowl < 3.4 g; bowl outer-circle radial jump for generatrix < 0.03 mm. Spindle-end radial jump after assembly <= 0.10 mm. 5-hour continuous test-run inspection before shipment.

Dimensions

Emprise au sol

Bench-top mounted via four foundation bolts onto rubber shock pads; level the machine via plummet centering on the feeding nozzle. Position voltage regulator control cabinet within easy view/reach of operator. Requires reliable ground connection.

Matériaux

Matériaux en contact

304 stainless steel for all material-wetted parts (bowl,spindle,nozzle,liquid collection pan,cover); PTFE seal washers; special grease for high-speed bearings

Matériaux du bâti

Cast machine body with rubber shock pads on four foundation bolts; aluminum belt cover with ball-nut fastener; high-speed belt; series single-phase motor with voltage regulator control cabinet

Caractéristiques principales

Bowl 42 mm ID x 225 mm H, 0.36 L volume

Variable speed 10,000-28,000 rpm (voltage regulator stepless, max 175 V)

Separation factor approximately 18,500 G

Continuous throughput 80 L/h (clarification mode)

Flexible-suspension spindle with spring-coupled upper/lower halves dampens vibration

Single-phase series motor + high-speed belt drive: smooth start, low noise

Check-valve bowl cover prevents back-flow contamination on stop

All wetted parts 304 stainless steel

Bench-top mountable via four foundation bolts on rubber shock pads

Bowl dynamic-balance precision A=2.5 grade; total de-weight of bowl < 3.4 g

Vibration intensity <= 7.1 mm/s (loaded and idling)

Load motor temperature rise <= 30 C; voltage regulator <= 25 C

5-hour continuous test-run validation before delivery

Bowl radial jump of spindle end <= 0.10 mm after assembly

Idle speed reduction allowable 1%; loaded 3% (per ZBJ7708-89)

Highest centrifugal force in bench-top class for ultra-fine particle separation

Suitable for small-batch, high-mix lab work and pilot bioengineering

Gives purer liquid + drier solid than basket centrifuges

Optional cooling coil enables temperature-sensitive bio separation

Modular: switch between clarification and 3-phase separation bowls

Stepless speed control without VFD (low-cost, simple, high-reliability)

Applications

Vegetable/animal oil refining (residue clarification)

Vaccine, blood serum and biological broth clarification

Lubricant and resin emulsion clarification

Pharmaceutical intermediate purification (lab/pilot)

Food fermentation broth solids removal

Fine chemical pigment/dye separation

Lab-scale yeast/bacteria recovery

Essential oil and fragrance clarification

Secteurs

Pharmaceutical (API, biologics)

Bioengineering / biotechnology

Edible oil and fat refining

Food fermentation

Fine chemical / pigment / dye

Vaccine / serum production

Research labs and pilot plants

SED

Échangez avec SED Sales Team

Spécialistes des équipements · contact sur WhatsApp

Consultez les horaires et la disponibilité de l’équipe

+86 139 5885 3738

Envoyer un e-mail Discuter sur WhatsApp →Demander un appel de 30 minutes →

Nettoyage et entretien

After bowl fills with solids: close feed valve, wait several minutes, press stop. After bowl fully halts, remove bowl with bowl wrench, open with bottom-shaft wrench, scrape solids out with scraper/rake, clean carefully, reinstall with attention to PTFE seal washer (leakage occurs if omitted). Lubrication: high-speed bearings every 2-3 months with special high-speed grease; sliding bearings in liquid-in seat are self-lubricating, apply a little grease at each use. Spindle (spring-coupled halves) repairs must be returned to manufacturer.