Accueil / Équipements / Formeuse, scelleuse et découpeuse de gobelets plastiques / Plastic Cup Form-Fill-Seal-Cut Machine

SED-12SQJ-P

Sur devis

SED-12SQJ-P

SED · SED-12SQJ-P · En vedette

SED-12SQJ-P — Plastic Cup Form-Fill-Seal-Cut Machine

La description complète de ce modèle est encore en cours de traduction. Consultez les détails en anglais ou demandez des informations à notre équipe. English

SED-12SQJ-P plastic-cup form-fill-seal-cut machine (8-row eight-up). Stainless-steel frame, Mitsubishi servo drive, 304 SS frame and contact parts; suited to liquid-food cup packaging. Capacity 10000 cups/h at 150 ml fil

Délai de livraison

Sur devis

Cadence

10000 cups/h

Fonctionnement

Sheet film (PET/PS, 0.8-1.0 mm thick, 290/310 mm wide) is unrolled onto stainless film-feed chains. An upper and lower magnesium-aluminum preheating plate (with non-stick coating) heats the sheet to forming temperature. The sheet then enters a forming station where pneumatic punches and dies (>=0.6 MPa) form 8 cups simultaneously. A balance-tank-fed dosing-piston system meters 150 ml per cup through pneumatic open/close fill valves; a CIP loop is built in for cleaning. Three-layer aluminum-plastic sealing film is unwound (electronic clutch + color-mark sensor + edge-correction) over the cups; a heated seal plate then seals each cup, followed by a separate cold-seal station. Three independent punch/cut stations perform punching, transverse cut and crease/scoring. Mitsubishi servo + precision reducer drives the main chain; Omron PLC + HMI + temperature controllers in a SS cabinet handle automation. Belkis centralized auto-lubrication and a clean-air positive-pressure shroud (with HEPA filtration and UV bactericide) keep the form-fill-seal area clean.

Processus de fonctionnement

1Sheet film (PET/PS, 0.8-1.0 mm thick, 290/310 mm wide) is unrolled onto stainless film-feed chains.

2An upper and lower magnesium-aluminum preheating plate (with non-stick coating) heats the sheet to forming temperature.

3The sheet then enters a forming station where pneumatic punches and dies (>=0.6 MPa) form 8 cups simultaneously.

4A balance-tank-fed dosing-piston system meters 150 ml per cup through pneumatic open/close fill valves; a CIP loop is built in for cleaning.

5Three-layer aluminum-plastic sealing film is unwound (electronic clutch + color-mark sensor + edge-correction) over the cups; a heated seal plate then seals each cup, followed by a separate cold-seal station.

6Three independent punch/cut stations perform punching, transverse cut and crease/scoring.

7Mitsubishi servo + precision reducer drives the main chain; Omron PLC + HMI + temperature controllers in a SS cabinet handle automation.

8Belkis centralized auto-lubrication and a clean-air positive-pressure shroud (with HEPA filtration and UV bactericide) keep the form-fill-seal area clean.

Caractéristiques techniques

Caractéristiques de la variante : SED-12SQJ-P

Caractéristiques

Modèle

SED-12SQJ-P

Cadence

10000 cups/h

Tension

Three-phase 5-wire 380 V / 220 V, 50 Hz

Fluides et énergie

Three-phase 5-wire 380 V / 220 V, 50 Hz, 23 kW total; compressed air 1.5 m^3/min @ >=0.8 MPa supply (forming >=0.6 MPa); cooling water 0.2 t/h for forming dies; air should be filtered for oil and water

Puissance

23 kW

Pression d’air

Forming pressure >=0.6 MPa; air-supply pressure >=0.8 MPa; consumption 1.5 m^3/min

Dimensions

Longueur

5350 mm

Largeur

920 mm

Hauteur

2300 mm

Poids

2300 kg

Emprise au sol

5350 x 920 x 2300 mm

Matériaux

Matériaux en contact

SUS304 stainless steel (frame, base, support plates, mounting plates, panels and contact components); Mg-Al alloy preheat and seal plates with non-stick coating

Matériaux du bâti

SUS304 stainless steel main frame and structural members; channel-steel + paint for the common base on shipping skid; SS electrical control cabinet

Caractéristiques principales

8-up plastic cup form-fill-seal-cut all-in-one

10000 cups/h at 150 ml; fill accuracy +/-2 %, seal pass rate >=98 %

All-SS 304 frame and contact parts; pharmaceutical/food friendly

Mitsubishi servo + precision reducer for main chain drive

Mg-Al alloy preheat plates with non-stick coating; long-life heating tubes

Pneumatic forming with stroke control

Balance-tank fill system, dosing-piston cylinder, pneumatic open/close fill valves, built-in CIP

3-layer aluminum-plastic sealing film with electronic clutch, color-mark, edge-correction

Heat-seal + separate cold-seal station with non-stick coating on seal plate

Three independent punch/cut stations: punching, transverse cut, crease/scoring

Omron PLC + HMI + temperature controllers in SS cabinet

Belkis centralized auto-lubrication

Clean-air positive-pressure shroud with filtration + UV sterilization (option)

All-stainless construction makes it well-suited to liquid-food production

Servo-driven indexing - accurate positioning, easy adjustment

Spray/drip-free fill system with low maintenance and long service life

Integrated CIP loop for in-place cleaning

Optional anti-static, UV sterilization and CIP loop with recovery tank

70-day delivery; on-site commissioning + training (overseas board, lodging, flights borne by buyer; engineer USD/day)

1-year warranty after commissioning (or 15 months after delivery)

13% VAT invoice; price includes domestic shipping to Shanghai port

Applications

Liquid-food cup packaging (yogurt, jelly, juice, water, cream)

Plastic cup form-fill-seal in 8-row layout

150 ml cup-format dosing with sealed lid

Secteurs

Liquid food and beverage

Dairy

Pharmaceutical liquid (cup format)

Marques des composants

Camozzi (Italy) or SMC (Japan) - cylinders and solenoid valves

Mitsubishi (Japan) - servo motors and controllers

IGUS (Germany) - linear bearings

Mitsubishi or Omron - PLC and industrial-control modules; touchscreen

Omron (Japan) - photoelectric, travel and proximity sensors

Schneider or ABB - low-voltage electrical

Belkis - centralized auto-lubrication

Suzhou Sujing / Freudenberg - air filtration

Yuan'an - pipe fittings and valves

SED

Échangez avec SED Sales Team

Spécialistes des équipements · contact sur WhatsApp

Consultez les horaires et la disponibilité de l’équipe

+86 139 5885 3738

Envoyer un e-mail Discuter sur WhatsApp →Demander un appel de 30 minutes →

Nettoyage et entretien

Built-in CIP loop with optional CIP recirculation pump and recovery tank; SUS304 contact parts and rounded geometry support wash-down. Optional UV sterilization in clean-air shroud after each batch.