Accueil / Équipements / Sécheur continu à lit fluidisé vibrant ZGF (avec refroidissement LZGF / granulation par pulvérisation PZGF) / Vibrating Fluid-Bed Dryer — SED-ZGF Series, 8000×1800 mm Bed

SED-8-1.8ZGF-H

Sur devis

SED-8-1.8ZGF-H

SED · SED-8-1.8ZGF-H · En vedette

SED-8-1.8ZGF-H — SED-ZGF Series, 8000×1800 mm Bed

La description complète de ce modèle est encore en cours de traduction. Consultez les détails en anglais ou demandez des informations à notre équipe. English

SED-8-1.8ZGF-H Vibrating Fluid-Bed Dryer is a continuous vibrating-bed dryer with 14.4 m² drying-bed area (8000 mm × 1800 mm) for drying, cooling, and humidifying granular materials in pharmaceutical, chemical, food, fru

Choisir une variante (6)

Délai de livraison

Sur devis

Cadence

290–420 kg/h evaporation

Fonctionnement

Wet material enters the bed at the inlet hopper. Two 7.5 kW vibration motors mounted on a vibrating frame propel the material forward in horizontal small jumps. Filtered hot air (70–140°C) is forced upward through the SUS304 perforated plate by the blower; the air-flow + vibration combination fluidizes the material so each particle is suspended in the hot stream and dries uniformly. The bed is divided into a high-pressure pre-drying zone (forces full fluidization), a low-pressure drying zone (carries away large quantities of water), and a cooling zone (high-flow ambient air to drop product temperature). Moist exhaust air leaves through a cyclone separator and induced-draft fan; the hot-air supply uses a steam radiator (or electric heater). Material discharges at the outlet. Adjusting motor swing-angle and air valves tunes residence time, layer thickness, and drying intensity.

Processus de fonctionnement

1Wet material enters the bed at the inlet hopper.

2Two 7.5 kW vibration motors mounted on a vibrating frame propel the material forward in horizontal small jumps.

3Filtered hot air (70–140°C) is forced upward through the SUS304 perforated plate by the blower; the air-flow + vibration combination fluidizes the material so each particle is suspended in the hot stream and dries uniformly.

4The bed is divided into a high-pressure pre-drying zone (forces full fluidization), a low-pressure drying zone (carries away large quantities of water), and a cooling zone (high-flow ambient air to drop product temperature).

5Moist exhaust air leaves through a cyclone separator and induced-draft fan; the hot-air supply uses a steam radiator (or electric heater).

6Material discharges at the outlet.

7Adjusting motor swing-angle and air valves tunes residence time, layer thickness, and drying intensity.

Caractéristiques techniques

Caractéristiques de la variante : ZGF-3×0.3 (0.9 m²

Caractéristiques

Modèle

SED-8-1.8ZGF-H

Cadence

290–420 kg/h evaporation

Tension

380V 50Hz 3Φ

Puissance

15 kW

Dimensions

Longueur

8520 mm

Largeur

3250 mm

Hauteur

3100 mm

Poids

8600 kg

Matériaux

Matériaux en contact

SUS304 stainless steel (bed plate, perforated plate, mat net, ductwork, air duct, intake/outlet pipes, feed hopper); silicon rubber bed seal; heat-resistant cloth soft connection

Matériaux du bâti

16# section steel bed-body bracket; A3 steel (2 mm) bed-body sealing material; SUS304 inner walls (full welded); A3 steel (2 mm) electric box

Caractéristiques principales

Drying-bed area 14.4 m² (8000 mm × 1800 mm)

Continuous fluidized-bed drying / cooling / humidifying

Two 7.5 kW vibration motors — smooth, low-noise operation

Three-zone airflow: pre-drying (high-pressure low-flow), drying (low-pressure high-flow), cooling

Quick-open upper/lower bed for thorough cleaning

Combined perforated plate: tongue holes (front) + straight holes (mid/rear)

Stainless-steel seamless-tube bed support and SUS304 inner walls (full welded)

Stainless-steel ductwork, blower, heater (no contamination of product)

Stepless adjustment of bed amplitude, layer thickness and material speed

Sealed structure prevents cross-contamination with outside air

30–60% energy savings vs general dryers

Cleaning port for in-place cleaning

SIEMENS electrical components

Largest size in the ZGF series — 14.4 m² for high-throughput pharma/chemical lines

Three-zone airflow design dries + cools in one continuous pass

Quick-open bed eliminates bolt-fixing — minutes-fast cleaning between batches

All-SUS304 wetted parts protect product purity

30–60% energy savings vs traditional dryers — major OPEX advantage at scale

Customer can choose electric or steam heating

Applications

Pharmaceutical granule drying (post-granulation)

Pharmaceutical material cooling and moisture control

Chemical / food / fruit / beverage / seed / slag drying

Simultaneous drying-cooling-humidifying lines

Brittle-particle drying (low surface damage)

Secteurs

Pharmaceutique

Chemical

Food and agriculture

Beverage

Seed processing

Industrial mineral / slag

Marques des composants

SIEMENS (Germany) — electrical components

Self-made — bed body bracket (16# section), perforated plate, mat net (SUS304 120-mesh), adjusting damper, air duct

Market supply (China) — bed sealing material (A3 steel), bed material (SUS304 3mm), blower, induced draft fan, vibrating motors (×2, 7.5 kW each), steam radiator (SUS304), anti-vibration rubber bowls (×20), bed seal (silicon rubber)

SED

Échangez avec SED Sales Team

Spécialistes des équipements · contact sur WhatsApp

Consultez les horaires et la disponibilité de l’équipe

+86 139 5885 3738

Envoyer un e-mail Discuter sur WhatsApp →Demander un appel de 30 minutes →