Accueil / Équipements / Autoclave à vide pulsé / SED-2.0MM-J Pulsating Vacuum + Water-Bath Dual-Use Sterilizer (with Safety Inspection Interface)
SED-2.0MM-J
Sur devis
SED-2.0MM-J
SED · SED-2.0MM-J · En vedette
SED-2.0MM-J — SED-2.0MM-J Pulsating Vacuum + Water-Bath Dual-Use Sterilizer
La description complète de ce modèle est encore en cours de traduction. Consultez les détails en anglais ou demandez des informations à notre équipe. English
SED-2.0MM-J Pulsating Vacuum + Water-Bath Dual-Use Sterilizer (with GMP validation/safety inspection interface). Horizontal pass-through autoclave with double-door (pneumatic motorised, gas-sealed, double-door interlocke
Délai de livraison
Sur devis
Cadence
600 L (chamber 1340x1000x1500 mm)
Fonctionnement
Saturated-steam sterilization with pulsating-vacuum air removal. Horizontal double-jacketed chamber: jacket pre-heated by 0.3–0.5 MPa industrial steam, then alternating pulsed vacuum + pure steam (multiple cycles) removes residual cold air before sterilization hold. After hold, vacuum drying + jacket-heated drying removes moisture. Water-bath mode: clean steam + air mixed overpressure with water immersion/spray for liquid loads in sealed containers. Full GMP validation interface with Siemens MES data extraction port. Cycle: preparation → preheat → vacuum → heat-up → sterilization → drying → end.
Processus de fonctionnement
1Saturated-steam sterilization with pulsating-vacuum air removal.
2Horizontal double-jacketed chamber: jacket pre-heated by 0.3–0.5 MPa industrial steam, then alternating pulsed vacuum + pure steam (multiple cycles) removes residual cold air before sterilization hold.
3After hold, vacuum drying + jacket-heated drying removes moisture.
4Water-bath mode: clean steam + air mixed overpressure with water immersion/spray for liquid loads in sealed containers.
5Full GMP validation interface with Siemens MES data extraction port.
6Cycle: preparation → preheat → vacuum → heat-up → sterilization → drying → end.
Caractéristiques techniques
Caractéristiques de la variante : SED-2.0MM-J
Caractéristiques
Modèle
SED-2.0MM-J
Cadence
600 L (chamber 1340x1000x1500 mm)
Tension
AC 380V 50Hz
Puissance
4.5 kW
Pression d’air
Compressed air 0.5-0.7 MPa (oil-free, water-free, dust-free); clean compressed air 0.2-0.3 MPa; pure steam 0.2-0.4 MPa; industrial steam 0.3-0.5 MPa (also stated 0.4-0.6 MPa); water 0.1-0.3 MPa
Dimensions
Longueur
1640 mm
Largeur
2060 mm
Hauteur
2200 mm
Poids
2300 kg
Matériaux
Matériaux en contact
316L stainless steel (inner chamber, door, instrument-side piping, internal safety valve, sterilizing carts); medical-grade silicone rubber (door gasket); medical/food-grade gaskets and O-rings
Matériaux du bâti
304 stainless steel jacket (autogenous gas-shielded full weld); 304 SS outer decorative panels; aluminium-silicate fibre insulation 60 mm (chlorine-free, asbestos-free)
Caractéristiques principales
Dual-use: pulsating-vacuum (steam) + water-bath sterilization in one machine
Pass-through double-door (motorised, gas-seal, interlocked) with pressure safety interlock
Pulsating vacuum air removal + vacuum drying + jacket-heated drying
316L SS inner chamber with chamfered/radius corners (no dead angles); 304 SS jacket (full autogenous weld)
ASCO (USA) angle-seat pneumatic valves rated 4M cycles (clamp connection, PTFE seal, 184°C steam rated)
Siemens S7 PLC (50,000 h MTBF) + touch screen + micro-printer (Epson chip) + paperless recorder
Swiss HUBA pressure transmitter + AIRIS Pt100 A-grade sensors (error ≤0.15°C)
Vacuum leak test: evacuate to −90 kPa, pump off 10 min, leakage ≤1.3 kPa
Sterilization time 0–600 min adjustable; temperature uniformity ≤±1°C
MES/network interface (Siemens extraction port) for data connectivity
Dual-use pulsating-vacuum + water-bath capability in a single pass-through autoclave
Imported precision components: Siemens PLC, ASCO valves, HUBA pressure transmitter, AIRIS temperature probes
Designed per Chinese cGMP, GB/T 150 pressure vessel, YY 0085.1, GB 18278.1, ISO and CE
GMP validation interface with DQ/IQ/OQ/PQ documentation support
Network/MES interface (Siemens extraction) for real-time data archiving
Applications
Sterilization of surgical instruments and metal tools
Sterilization of dressings and sterile garments / textiles
Liquid (culture media) sterilization
Glassware sterilization
Bowie & Dick steam-penetration test
GMP validation runs (IQ/OQ/PQ)
Secteurs
Hospitals
Fabrication pharmaceutique
Veterinary drug manufacturing (per GMP 2020 vet)
Scientific / experimental animal research
Marques des composants
Angle-seat pneumatic valve (clamp, PTFE, 4M cycles, 184°C rated)
ASCO
Water-ring vacuum pump (direct-coupled, mechanical seal, low noise)
Yulong
Circulation pump
WILO
Plate heat exchanger
Huisituo
Air filter (0.22 µm, sterile grade)
Jiangsu Santong
Solenoid valve
AirTAC
Steam trap
CIS
Pressure gauge
Brady (Beijing)
Safety valve (0.1–0.3 MPa)
Guangyi (Zhejiang)
Spray nozzle (spiral, large flow, wide angle, non-clogging)
Sborun
PLC (S7 series, 50,000 h MTBF)
Siemens
Touch screen
TER
Micro printer (Epson chip, sterilization report + temp trend)
Weihuan (Beijing)
Paperless recorder
Unspecified
Pressure transmitter (high precision, anti-interference)
HUBA
Temperature probe (Pt100, A-grade, ≤0.15°C error)
AIRIS (Airuisi)
Sterilizing carts (316L SS, 2 units)
SED
Transport carts (304 SS, 2 units)
SED
SED
Échangez avec SED Sales Team
Spécialistes des équipements · contact sur WhatsApp
Consultez les horaires et la disponibilité de l’équipe
Conformité
China GMP (2010 revision)
China Pharmacopoeia 2020 edition
GB/T 150.1–150.4-2011 pressure vessels
YY 0085.1-1992 Pulsating vacuum pressure steam sterilizer
GB 18278.1-2015 industrial moist-heat sterilization
ISO standard
CE standard
GB 50447-2008, GB 14952-2010 (animal research facility)
GMP validation interface (DQ/IQ/OQ/PQ documentation)
Nettoyage et entretien
316L SS internal surfaces with chamfered corners and no dead angles for easy cleaning; silicone rubber door gasket cleaned with ordinary surface cleaning (no lubrication required)
Documentation
Fiche technique (PDF)
Aperçu de l’équipement, caractéristiques et dimensions · Document d’origine (anglais)
Demander au service commercial
Manuel opérateur
Installation, fonctionnement et dépannage · Document d’origine (anglais)
Demander au service commercial
Fiche comparative (Standard et Économique)
Comparaison des configurations · Document d’origine (anglais)
Demander au service commercial
Protocoles IQ / OQ / PQ
Documentation de validation pour la conformité GMP · Document d’origine (anglais)
Demander au service commercial
Protocoles FAT / SAT
Essais de réception en usine et sur site · Document d’origine (anglais)
Demander au service commercial
Plans CAD (STEP / IGES / DWG)
Plans d’ingénierie pour l’implantation · Document d’origine (anglais)
Demander au service commercial
Certificats d’étalonnage
Niveau sonore, résistance de terre, rigidité diélectrique et rugosité · Document d’origine (anglais)
Demander au service commercial
DQ (qualification de la conception)
Protocole complet de qualification de la conception · Document d’origine (anglais)
Demander au service commercial
Certificats matières
Composition de l’acier inoxydable 316L · Document d’origine (anglais)
Demander au service commercial