Inicio / Equipos / Secador centrífugo industrial de gran capacidad (≥100 kg/h) / High-Speed Centrifugal Spray Dryer (400 kg/h Water Evaporation)
SED-400PG-T
Consultar
SED-400PG-T
SED · SED-400PG-T · Destacado
SED-400PG-T — High-Speed Centrifugal Spray Dryer
La descripción completa de este modelo aún se está traduciendo. Consulte los detalles en inglés o solicite información a nuestro equipo. English
SED-400PG-T High-Speed Centrifugal Spray Dryer System. Water evaporation capacity 400 kg/h. Centrifugal (rotary) atomization at up to 15,500 rpm. Designed for feed moisture ~60%, drying to ~5% product moisture. Inlet air
Plazo de entrega
Consultar
Capacidad de producción
340–420 kg water evaporation/h
Funcionamiento
Feed slurry is pumped by a variable-frequency feed pump (GF30-2, 1.1 kW, 0.1–1.1 m³/h, max 0.8 MPa) to a vertical two-stage gear-driven centrifugal atomizer (JGP-400, 5.5–7.5 kW). The atomizer disk (Φ150 mm, 15,500 rpm, line speed >120 m/s) instantly disperses feed into fine droplets. A gas-fired hot-air furnace (JRF5-60, natural gas 60 m³/h) heats air to 200–250 °C; a 15 kW supply fan (4-72-6C, 10,314–20,628 m³/h) delivers the hot air through a filter and ductwork to the adjustable hot-air distributor at the tower top. Hot air and atomized droplets contact inside the 4.5 m Φ drying tower: water evaporates instantly, leaving dry powder. Most product exits the tower base via discharge valve; residual fines follow exhaust gas through a CLK-1350 cyclone separator for secondary collection. Exhaust is drawn by a 37 kW induced-draft fan (9-26-9D, 12,518–19,719 m³/h) through a wet-scrubber for environmental tail-gas treatment before discharge. An air-hammer system on the tower cone prevents powder adhesion. PLC centrally monitors and controls all subsystems.
Proceso de funcionamiento
1Feed slurry is pumped by a variable-frequency feed pump (GF30-2, 1.1 kW, 0.1–1.1 m³/h, max 0.8 MPa) to a vertical two-stage gear-driven centrifugal atomizer (JGP-400, 5.5–7.5 kW).
2The atomizer disk (Φ150 mm, 15,500 rpm, line speed >120 m/s) instantly disperses feed into fine droplets.
3A gas-fired hot-air furnace (JRF5-60, natural gas 60 m³/h) heats air to 200–250 °C; a 15 kW supply fan (4-72-6C, 10,314–20,628 m³/h) delivers the hot air through a filter and ductwork to the adjustable hot-air distributor at the tower top.
4Hot air and atomized droplets contact inside the 4.5 m Φ drying tower: water evaporates instantly, leaving dry powder.
5Most product exits the tower base via discharge valve; residual fines follow exhaust gas through a CLK-1350 cyclone separator for secondary collection.
6Exhaust is drawn by a 37 kW induced-draft fan (9-26-9D, 12,518–19,719 m³/h) through a wet-scrubber for environmental tail-gas treatment before discharge.
7An air-hammer system on the tower cone prevents powder adhesion.
8PLC centrally monitors and controls all subsystems.
Especificaciones técnicas
Especificaciones de la variante: SED-400PG-T
Especificaciones
Modelo
SED-400PG-T
Capacidad de producción
340–420 kg water evaporation/h
Tensión
380V, 3-phase
Suministros
380 V, 3-phase. Total power: feed pump 1.1 kW + atomizer 5.5 kW + supply fan 15 kW + induced fan 37 kW + circulating water pump 1.5 kW ≈ 60.1 kW total. Natural gas: 60 m³/h for hot-air furnace. Cooling water for atomizer oil-cooling circulating loop.
Detalles de conformidad
Material-contact parts 304/316L stainless steel throughout. Tower design verified: effective drying volume 128 m³, drying intensity 3.0 kg water/m³·h, actual capacity 384 kg water/h (spec ≥375 kg/h). Empty-tower velocity 0.195 m/s (within normal operating range). Wet-scrubber tail-gas treatment for environmental compliance.
Dimensiones
Superficie de instalación
Drying tower Φ4.5 m base; total system footprint (tower + cyclone + fans + furnace + control cabinet) requires site engineering. Tower height: 4.5 m cylinder + 4.5 m cone (plus top equipment ~3 m clearance needed)
Materiales
Materiales en contacto
316L stainless steel for all material-contact surfaces: feed pump, feed pipe, atomizer body and disk, drying tower inner wall, hot-air distributor, observation door, sight glass, outlet duct, discharge valve, cyclone separator and discharge valve
Materiales del cuerpo
Drying tower inner wall: 316L SS; frame and support: carbon steel; tower outer wall: stainless steel; insulation: rock wool (100 mm tower top); supply and induced fans: carbon steel; gas furnace: carbon steel; ducts: carbon steel with rock-wool insulation; tail-gas pipe and chimney: carbon steel
Características principales
Water evaporation capacity 400 kg/h
Centrifugal rotary atomization, max 15,500 rpm, disk Φ150 mm, line speed >120 m/s
Vertical two-stage gear-driven atomizer; SKF imported main bearings; Harbin radial-thrust ball bearings; alloy-steel forged, heat-treated, ground shafts and gears
Atomizer pump-oil external forced cooling
Feed pump GF30-2: 1.1 kW, 0.1–1.1 m³/h, max 0.8 MPa, variable-frequency
Drying tower Φ4.5 m, cylinder 4.5 m + cone 4.5 m (128 m³ effective volume)
Adjustable hot-air distributor angle 15–45° — reduces wall sticking
6 air hammers on tower cone prevent powder adhesion
Cyclone separator CLK-1350 for secondary product collection
Supply fan 4-72-6C, 15 kW, 10,314–20,628 m³/h
Induced-draft fan 9-26-9D, 37 kW with variable-frequency drive
Wet-scrubber (water film dust collector) on tail gas
PLC central control of all subsystems
All material-contact parts in 316L stainless steel
Tower interior: 316L SS inner wall, rock-wool insulation, cleaning door (500×600 mm), internal lighting
Large-capacity continuous spray drying (400 kg water/h evaporation)
Adjustable hot-air distributor angle reduces tower wall sticking
Air-hammer cone clears stuck powder automatically
Imported SKF main bearings in atomizer for long service life
Wet scrubber on tail gas for environmental compliance
Variable-frequency feed pump and induced-draft fan for tunable throughput
316L stainless steel material-contact surfaces for pharmaceutical-grade hygiene
Comprehensive product collection: tower discharge + cyclone secondary collection
Aplicaciones
Spray drying of pharmaceutical solutions and extracts
Spray drying of traditional Chinese medicine (TCM) extracts
Spray drying of food slurries (dairy, etc.)
Spray drying of biological cultures
Spray drying of chemical and agrochemical solutions
Sectores
Farmacéutico
Traditional Chinese medicine
Food
Biotecnología
Chemical
Marcas de componentes
SKF (Sweden) — main bearing in centrifugal atomizer
Harbin (China) — radial thrust ball bearings for drive and intermediate shafts
JGP-400 atomizer — in-house/domestic, 5.5–7.5 kW
GF30-2 feed pump — domestic, 1.1 kW, variable-frequency
JRF5-60 gas-fired hot-air furnace — domestic, 60 m³/h natural gas
Supply fan 4-72-6C (15 kW) — domestic
Induced-draft fan 9-26-9D (37 kW) with variable-frequency drive — domestic
CLK-1350 cyclone separator — domestic
SED
Hable con SED Sales Team
Especialistas en equipos · contacto por WhatsApp
Consulte el horario y la disponibilidad del equipo
Documentación
Ficha técnica (PDF)
Resumen del equipo, especificaciones y dimensiones · Documento original (inglés)
Solicitar al equipo comercial
Manual del operador
Instalación, funcionamiento y diagnóstico · Documento original (inglés)
Solicitar al equipo comercial
Ficha comparativa (Estándar y Económica)
Comparación de configuraciones · Documento original (inglés)
Solicitar al equipo comercial
Protocolos IQ / OQ / PQ
Documentación de validación para conformidad GMP · Documento original (inglés)
Solicitar al equipo comercial
Protocolos FAT / SAT
Pruebas de aceptación en fábrica y en sitio · Documento original (inglés)
Solicitar al equipo comercial
Planos CAD (STEP / IGES / DWG)
Planos de ingeniería para la instalación · Documento original (inglés)
Solicitar al equipo comercial
Certificados de calibración
Nivel sonoro, resistencia de tierra, rigidez dieléctrica y rugosidad · Documento original (inglés)
Solicitar al equipo comercial
DQ (cualificación del diseño)
Protocolo completo de cualificación del diseño · Documento original (inglés)
Solicitar al equipo comercial
Certificados de materiales
Composición del acero inoxidable 316L · Documento original (inglés)
Solicitar al equipo comercial